Embroidery Machine Tajima Error Codes | Full Guide (2024)

These are some frequent errors that Tajima embroidery machine users may encounter. Each code helps identify specific issues, making troubleshooting easier and faster.

1. 3D6 Error Code
2. BC1 Error Code
3. 2B1 Error Code
4. 2B2 Error Code
5. 2B3 Error Code
6. 2B4 Error Code
7. 2B5 Error Code
8. 211 Error Code
9. 311 Error Code
10. 312 Error Code
11. 313 Error Code
12. 314 Error Code
13. 316 Error Code
14. 321 Error Code
15. 322 Error Code

Each error code highlights the cause of a specific issue with the Tajima embroidery machine. By understanding the reason behind each error, we can apply targeted solutions to fix the problem efficiently.

The Tajima 3D6 error code indicates that the machine’s program has encountered an abnormal state, often due to issues with the CPU card or its software.

Solutions

1. Reinstall Software: Use the original installation disk or download the latest software version from the Tajima website to reinstall the software on the CPU card.
2. Check CPU Card Installation: Ensure that the CPU card is securely connected and properly seated in its slot. Reseat it if necessary.
3. Consult Technical Support: If issues persist after reinstalling software, contact Tajima support for further assistance.
4. Perform a System Reset: Some models allow for a system reset; refer to your user manual for instructions.

2. BC1 Error Code

The BC1 error code Tajima indicates that the selected design is not found on the floppy disk or no design is registered on the disk.

Solutions

1. Check Disk for Designs: Ensure that the floppy disk contains valid design files. Try using a different disk if necessary.
2. Verify Disk Compatibility: Ensure that the floppy disk is compatible with your machine model.
3. Select Another Design: If the current design cannot be found, try selecting a different design from the disk.
4. Inspect Disk Drive: Check for any mechanical issues with the floppy disk drive itself.

3. 2B1 Error Code

Solutions

1. Verify Serial Connections: Check that all serial interface devices are correctly connected and powered on.
2. Restart Devices: Power cycle both the embroidery machine and any connected devices to refresh their connections.
3. Correct Design Data Issues: Ensure there are no issues with design data being sent from connected devices; recheck file formats and compatibility.
4. Inspect Communication Cables: Look for any damaged cables that may interrupt communication.

4. 2B2 Error Code

This error indicates an issue with stitch data where complementary codes are incorrectly entered. It’s one of the various Tajima errors related to data input.

Solutions

1. Correct Data Input Errors: Review your design data carefully for any input errors and correct them as needed.
2. Re-enter Design Data: If necessary, re-enter your design data into your embroidery software to ensure accuracy.
3. Use Compatible Software Versions: Ensure you are using software versions compatible with Tajima machines.

5. 2B3 Error Code

This error occurs when there is unexpected data at the end of a code sequence. Errors like this fall under Tajima error codes that often need data reformatting.

Solutions

1. Review Design Data Format: Check your design data for proper formatting; remove any extraneous information at the end of your code sequences.
2. Re-save Design Files Properly: Save your design files again in a compatible format recognized by your Tajima machine.
3. 1 DFA: This is an additional error identifier that may be relevant to this error code.

6. 2B4 Error Code

Indicates that there is an incorrect format in stitch codes being read by the machine, which is another issue in errors.

Solutions

1. Check Stitch Code Formatting: Verify that all stitch codes conform to Tajima’s required format.
2. Use Compatible Design Software: Ensure you are using compatible software designed specifically for Tajima machines when creating designs.

7. 2B5 Error Code

This error indicates that stitch data exceeds permissible limits set by the machine, adding to the list of Tajima errors related to design complexity.

Solutions

1. Adjust Stitch Lengths in Design File: Review your design file and adjust any stitch lengths that exceed 5.1 mm.
2. Simplify Complex Designs if Necessary: If certain designs are too complex, consider simplifying them or breaking them into smaller parts before stitching.

8. 211 Error Code

Solutions

1. Return Main Shaft to Fixed Position: Manually adjust the main shaft to its designated position according to the user manual.
2. Check Encoder Signal Functionality: Inspect and clean the encoder; ensure it is functioning correctly.
3. Power Cycle the Machine: Turn off and restart the machine to reset temporary errors.
4. Inspect Mechanical Components: Check for obstructions or damage in the mechanical components.

9. 311 Error Code

Solutions

1. Inspect Motor and Belt for Damage or Wear: Look for any signs of wear and tear on the motor and belt.
2. Check Encoder Connections: Ensure that the encoder is properly connected.
3. Test Motor Functionality: Run a motor test to check for issues.
4. Lubricate Moving Parts: Regularly lubricate the machine’s moving parts to prevent wear.

10. 312 Error Code

Similar to error code 311, this error indicates an issue with Encoder Z not registering changes over time during operation.

Solutions

1. Inspect Encoder Z Connections: Check connections to ensure Encoder Z is connected properly.
2. Test Functionality of Encoder Z: Run tests to ensure the encoder is operating correctly.
3. Replace Faulty Components: Replace any components that may be causing the issue.
4. 1 DFA: This identifier might be relevant for troubleshooting this specific error code.

11. 313 Error Code

This error indicates that the clutch stopper has disengaged unexpectedly, disrupting normal stitching operations, making it one of the Tajima error codes related to mechanical issues.

Solutions

1. Engage Clutch Stopper Manually: Manually re-engage the clutch stopper if possible.
2. Check for Mechanical Obstructions: Look for obstructions that may have caused the clutch stopper to disengage.
3. Consult User Manual: Refer to the user manual for specific instructions on re-engaging the clutch stopper.

12. 314 Error Code

This error suggests there is a failure in rotating the main shaft due to mechanical issues or motor problems.

Solutions

1. Check Encoder Signal Lines: Ensure all encoder signal lines are properly connected and functioning.
2. Inspect Belts for Wear or Damage: Check the belts for signs of wear and replace them if needed.
3. Lubricate Moving Parts Regularly: Ensure all moving parts are well-lubricated to facilitate smooth rotation.

13. 316 Error Code

This code indicates an issue with the driver responsible for controlling main shaft movement, potentially due to electrical faults or component failure, falling under Tajima code errors.

Solutions

1. Replace Main Shaft Driver Unit: If necessary, replace the main shaft driver unit.
2. Check Wiring and Connections: Inspect all wiring and connections related to the driver unit.
3. Perform Electrical Tests: Conduct electrical tests to identify potential issues.
4. 1 DFA: This additional identifier may be relevant for troubleshooting this error.

14. 321 Error Code

Solutions

1. Inspect Driver and Motor Connections: Ensure that all connections are secure.
2. Replace Faulty Components: Replace components within the PMD if they appear faulty.
3. Perform Regular Maintenance Checks: Regularly inspect and maintain the PMD units.

15. 322 Error Code

This error indicates an issue specifically related to X-axis movement control through its pulse motor driver system, included in the Tajima code errors.

Solutions

1. Check Thread Trimming Drive Card and Connections: Ensure that connections to the thread trimming drive card are secure.
2. Replace Damaged Components: Replace any damaged components related to X-axis movement.
3. Test X-Axis Movement Independently: Test the X-axis movement to ensure it functions properly.

Understanding Tajima error codes can make a big difference in keeping your embroidery machine running smoothly. Knowing the cause of each error helps you fix problems quickly and with confidence.

If you’re looking for expert digitizing services, our company offers the best quality at the most affordable rates, with a super-fast turnaround time and guaranteed quality. Plus, we provide a preview option so you can see your design before finalizing it.

And if it’s your first time with us, you’ll enjoy a 50% discount! Let us help bring your embroidery designs to life, hassle-free.